Graph paper types and sizes, explained
What each kind of printable paper is for, the spacing it normally uses, and how to make it in Gridfunction. Every link opens the generator with that layout loaded.
Square graph paper
The everyday grid. In the United States the standard is quarter-inch squares (four per inch), usually with a heavier line every inch. Elsewhere the standard is 5 mm squares with a heavier line every 5 or 10 squares. Gridfunction fits a whole number of squares inside your margins and centers them, so every sheet ends on a complete square. You can type any size, as a fraction (3/16) or a decimal (0.2). Make graph paper.
Engineering paper
Engineering computation pads use five squares per inch (1/5 in, about 5.08 mm) with a heavier line every inch and a header strip for the project, date and page number. They are traditionally printed in pale green so the grid stays in the background of handwritten work; pick the green swatch to match. Make engineering paper.
Millimeter paper
Fine 1 mm squares with medium lines every 5 mm and heavy lines every 10 mm, for accurate plotting and drafting. The grid is trimmed to whole centimeter blocks. Make millimeter paper.
Dot grid and cross grid
Dots mark the corners of an invisible square grid, which gives you structure without busy lines. 5 mm dots are the bullet-journal standard; quarter-inch dots are common in the US. A cross grid places small plus signs at the same points instead. Make dot grid paper or a cross grid.
Coordinate plane
A square grid with centered x and y axes and numbered tick marks, used for graphing functions and plotting points. The number of squares is always even in both directions, so both axes land exactly on grid lines. Numbers appear at the bold lines, and less often when the squares are very small. Make a coordinate plane.
Isometric, isometric dot and triangular paper
Isometric paper has vertical lines plus two sets of lines at 30° to the horizontal, which matches the three axes of an isometric drawing. It is the standard sheet for sketching 3D objects, rooms and game levels. Isometric dot paper shows only the corner points. Triangular paper uses the same equilateral triangles turned so one side of each triangle is horizontal, which suits quilting, tessellations and geometry lessons. Isometric, isometric dots, triangular.
Polar and log polar paper
Polar paper has concentric circles and radial spokes for plotting angles and distances, such as antenna patterns, wind roses and polar equations. Spokes that are not multiples of 30° stop short of the center so the middle stays readable, and degree labels run around the outside. Log polar paper spaces the rings on a logarithmic scale. Polar or log polar.
Semi-log and log-log paper
Logarithmic paper turns exponential growth and power laws into straight lines. Each cycle covers one power of ten, and the lines inside it are spaced at the logarithms of 2 to 9.
- Semi-log (y) has a logarithmic vertical axis and a linear horizontal axis, for growth or decay over time. Cycles start at the bottom, so values increase upward as on any graph.
- Semi-log (x) puts the logarithmic scale across the page, for frequency response and similar plots.
- Log-log paper is logarithmic on both axes. Gridfunction keeps every cycle the same length on both axes, so the slope you measure with a ruler equals the exponent of the power law.
Choose between one and five cycles; the cycle numbers 1 to 9 are printed along the edges. Semi-log or log-log.
Lined paper
US notebook paper comes in three standard rulings, all available with a red margin line about 1¼ inches from the left edge:
| Ruling | Line spacing | Typical use |
|---|---|---|
| Narrow ruled | 1/4 in (6.35 mm) | Small handwriting, more lines per page |
| College ruled | 9/32 in (7.1 mm) | Middle school to college notes |
| Wide ruled | 11/32 in (8.7 mm) | Younger students |
Metric lined paper is commonly 6 to 10 mm apart, with 8 mm the most common in many countries. Make lined paper or wide-ruled paper.
Handwriting practice paper
Each row has a solid top line, a dashed midline and a heavier baseline, followed by a blank gap for descenders. Letter heights of 1/2 or 5/8 inch suit kindergarten and first grade; 3/8 inch suits older students. Make handwriting paper.
Calligraphy guide sheets
Each row marks the ascender line, the x-height (dashed), the baseline and the descender line, with optional slant lines. Copperplate and Spencerian scripts usually slope at about 55°, while italic hands lean only 5 to 10 degrees from vertical, which is close to the 83° option. Make calligraphy paper.
Cornell notes
The Cornell layout divides a page into a narrow cue column on the left (about 2½ inches on a letter sheet), a wide notes column, a title band at the top and a summary area at the bottom (about 2 inches). Make Cornell notes paper.
Music staff paper
Five-line staves spaced evenly down the page. The setting is the distance between two staff lines; 2 mm is typical for general use and 2.5 to 3 mm is easier for beginners. Only complete staves are drawn. Make staff paper.
Hexagon, diamond, brick and perspective paper
Hexagonal paper is used for game maps, chemistry diagrams and quilting; diamond (diagonal) grids for patterns and lettering; brick grids for textures and masonry plans; and one-point perspective guides for drawing rooms and streets that recede to a vanishing point on the horizon. Hexagons, diamonds, bricks, perspective.
Printing at the correct size
- Choose the same paper size in Gridfunction and in your print dialog. An A4 page printed on US Letter paper (or the reverse) will be shrunk.
- Download the PDF. It has the exact page size and asks your PDF reader to print at actual size.
- In the print dialog, choose Actual size or 100% and turn off Fit to page.
- Measure ten squares with a ruler. Ten quarter-inch squares should measure 2½ inches; ten 5 mm squares, 50 mm. For layouts without squares, turn on Size-check ruler: it prints a short ruler in the bottom margin to hold a real ruler against.